MHT200Owner’s ManualMcIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 FAX: 607-724-0549A/V S
10Rear Panel Switch, Loudspeaker and Control ConnectionsConnect the MHT200power cord to a liveAC outlet. Refer to in-formation on the backpanel to det
11Rear Panel Audio and Digital ConnectionsEIGHT CHANNEL INPUTsaccept signals from a componentsuch as DVD-Audio/SACDPlayers or an external processor.ZO
12Rear Panel Video ConnectionsVIDEO INPUTS (1 thru 7) are for bothS-Video and Composite Video Signalsfrom a AUX, CD, SAT, TV, DVD,VCR1or VCR2 componen
13McIntosh MVP851 DVD Player Home ControllerHow to Connect for Data and Power ControlIR SensorHow to Connect for Data and Power ControlMcIntosh WK-4 K
14Caution: The supplied AC Power Cord should not beconnected to the Rear Panel of the MHT200Amplifier until after the Loudspeaker, Audio andVideo Conn
15Center FrontLoudspeakerHow to Connect LoudspeakersLeft SurroundLoudspeakerBack SurroundLoudspeakerRight SurroundLoudspeakerRight FrontLoudspeakerLef
16McIntosh MVP851 DVDHow to Connect Audio and Digital ComponentsHow to Connect Audio and Digital ComponentsThe MHT200 accepts Analog Audio and Digital
17McIntosh MVP851 DVDMonitor/TVHow to Connect Video ComponentsHow to Connect Video ComponentsComposite, S-Video and Component Video Signals can beconn
18Monitor/TVHow to Connect for Zone BHow to Connect for Zone BThe MHT200 is a Dual Zone A/V System Controller. ForZone B activation a McIntosh Sensor
19Front Panel Controls, Sensor and JacksSelects the Trim Func-tion for making audioand front panel displayadjustmentsIR (Infra Red) Sensor ac-cepts IR
2IMPORTANT SAFETYINSTRUCTIONS!PLEASE READ THEM BEFOREOPERATING THIS EQUIPMENT.WARNING - TO REDUCE RISK OFFIRE OR ELECTRICAL SHOCK, DONOT EXPOSE THIS E
20Tunes Up or Down the AMor FM Broadcast Band orPresets when the TM1Tuner Module is installedand allows up or down ad-justment for each trim func-tion
21Front Panel DisplaysIndicates when the PowerGuard Circuit has been acti-vated for the Left Front, Center,Right Front, Left Surround,Right Surround o
22Remote Control Push-ButtonsSelects one of the eightAudio/Video SourcesTurns AC Power ON or OFF tocertain McIntosh Componentswhen connected via the D
23How to Operate by Remote ControlHow to Operate by Remote ControlThe supplied Remote Control is capable of directly control-ling the functions of con
24Your McIntosh MHT200 has been factory configured fordefault operating settings that will allow immediate enjoy-ment of superb video and high fidelit
25SETUPThe following listings indicate the factory default settings.Refer to the listed page number for instructions on how tochange a default setting
26Analog Inputs (Zones A and B):Number Name Refer to Page1 ... AUX ... 362 ... C
27How to Adjust for Loudspeaker SizeA Home Theater System can include a variety of Loud-speakers with various capabilities. The LARGE listing re-fers
28How to Adjust Speaker LevelsA properly setup Home Theater Surround Sound Systemshould have all Loudspeaker Sound Levels adjusted to thesame starting
29settings on the SPEAKER LEVEL MENU are com-plete, select EXIT on the menu. The SPEAKERSETUP Menu will reappear on the Monitor/TV screen.9. Continue
3ground for the lead-in wire to an antenna dis-charge unit, and size of ground conductors, loca-tion of antenna-discharge unit, connection toground el
30Figure 20settings on the SPEAKER LEVEL MENU are com-plete, select EXIT on the menu. The SPEAKERSETUP Menu will reappear on the Monitor/TV screen.10.
31How to Adjust Speaker Time DelayThe following Time Delay Adjustments will electronicallycompensate for different Loudspeaker distances from theListe
32Location Default Setting New SettingLeft Front 10 Center 10Right Front 10 Right Surround 10Right Back noneLeft Back10Left Surround10Subwoofer10Lou
33cylindrical microphone body below the Power On/Offcounterclockwise. Make sure the battery is installedinto the microphone, with the battery polarity
34YES to save those changes or NO not to save them.The MHT200 will then return to normal operation. Re-fer to figure 13 on page 25.Dolby LFE LevelThe
35SETUP, con’tFigure 27MENU: SUBWOOFER SETTINGS1. MC BASS MODE Off2. SUB CROSSOVER 80 Hz3. DOLBY LFE LEVEL 0dB4. SUB FILTER OnEXIT10. Contin
36How to change Source SettingsThe MHT200 Setup Mode Source Settings allow any of theseven Analog Audio/Video Inputs, six Digital Audio Inputsand two
37Digital InputThere are three Optical Digital Inputs and three CoaxialDigital Inputs available for assignment with any of theseven Analog Audio Input
38for various inputs so that they have the same relative vol-ume. The Default Volume Level Setting for all Inputs is0dB and each input has a range of
39Figure 35MENU: SOURCE SETTINGS1. SOURCE INPUT 62. TITLE VCR13. DIGITAL INPUT Opt C4. COMPONENT INPUT 15. INPUT LEVEL6. TRIM PRESETS No Change7. TRI
4OperationHow to Operate the MHT200 ... 45How to Make a Recording ...
40Analog Audio and Video Inputs Source SettingsSource Numbe r Default Title New Title Default Trim Leve l New Trim Level Prese t Trim Number1 AUX 0dB2
41The MHT200 VIDEO POWER CONTROL Setup allowsselecting a specific Video Input or all Video Inputs to acti-vate the VIDEO POWER CONTROL Jack. This can
42How to change Mode SetupThe MHT200 allows for modifications in how the DolbyDigital Prologic II, DTS NEO:6 and the built-in Music 1thru 4 Sound Proc
43SETUP, con’tFigure 40MENU: SYSTEM SETUP1. VIDEO NTSC2. TUNER USA3. TEMP DISPLAY Full4. OSD ROUTING Both5. VIDEO FORMAT AutoEXITHow to change System
44How to Reset the MHT200If it should become necessary to reset the MHT200 to theDefault Settings, follow the procedure below:Notes: 1. First, if you
45cated on the left side of theFront Panel AlphanumericDisplay. Refer to figure 42.Note: The INPUT SelectorSwitch also selects theRecord Output forrec
46depending on the settings of the individual TRIM Levelsand SURROUND Mode.System OffNormally, each Zone is turned On and Off individually bypressing
47How to Operate the MHT200, con’tC. The DTS Display will illuminate when the input con-tains DTS Encoded Signals.D. The EXPAND Display will illuminat
48When the MHT200 has the optional TM1 AM/FM TunerModule installed, the On-Screen Display will indicate theFrequency and Preset Label. Press the Front
49The INPUT Selector Switch together with the Zone BPush-button allows making a recording from one programsource while listening to another. You can a
5General Notes and Connector Information1. It is recommended that a qualified professional assist you inthe choice and installation of a McIntosh Thea
50How to Operate the Trim ModeThe MHT200 TRIM SELECT Switch together with theTRIM LEVEL Control provide the means for adjustingfive different audio fu
512. Press and release the LEVEL Up Push-button untilthe +10 appears to the right of BASS TRIM on theFront Panel Alphanumeric Display. This is an exa
52How to Operate the Surround ModeThe MHT200 provides eight different Surround Modes,with one Mode with two functions. The Front Panel Alpha-numeric D
53How to Operate the MHT200, con’tFigure 70Figure 66Figure 67Figure 68Cinema 2 The Front Panel Alphanumeric Display will indicate CIN-EMA 2 and the ap
54How to Operate Zone BThe MHT200 includes the capability of being able to oper-ate and control two audio/video zones, independently ofeach other. Zon
55How to Operate the MHT200, con’t3. If a McIntosh Disc Player is connected to theMHT200, most operating functions can be performedwith the Keypad or
56Frequency ResponseLeft, Center, Right,Left Surround,Right Surround,Left Back, Right Back:±0.5dB from 20Hz-20,000HzSubwoofer1:±0.5dB from 20Hz-140HzR
57Power Amplifer and General SpecificationsGeneral SpecificationsPower Requirements100 Volts, 50/60Hz at 8.4 Amps110 Volts, 50/60Hz at 7.7 Amps120 Vol
58••••• Special FM RF AmplifierDouble-Diffused Metal Oxide Field Effect Transistor(DMOS-FET) RF amplifier increases sensitivity and CrossModulation re
59MHT200 Rear Panel and RAA1 Top Panel Antenna Connections75ohm FM ANT(Antenna) connectsto an external FMantenna or cableAM ANT (An-tenna) connectoral
6Connector InformationKeypad Terminal ConnectorTo use a WK-3 or WK-4 keypad with the MHT200, con-nect the shield and four leads of a shielded 4 conduc
60How to Connect Antenna ComponentsFM Antenna1. Connect the Remote AM antenna by plugging the DINconnector of the supplied 3 conductor cable into theA
61How to Assign Tuner PresetsTUNER SETUPThe MHT200 Setup Mode Tuner Presets allow for the pre-setting into memory 9 FM and 9 AM Radio Stations forfast
62locations other than the US where stations change in50Hz steps. AM Broadcast Band Indications are inkilohertz and change frequency in 10kHz steps.La
63TUNER SETUP, con’tFigure 82MENU: TUNER PRESETS1. PRESET FM12. TUNING MODE Auto3. FREQUENCY 91.50 MHz4. LABEL KABC
64How to Operate the TunerThe McIntosh MHT200 TM1 AM/FM Tuner Module in-corporates an advanced design AM/FM Tuner with manydesirable performance featu
65How to Optimize AM ReceptionThe McIntosh RAA1 Remote AM Antenna is designed toprovide the best in AM Reception especially if the tuner orA/V unit is
66FM Tuner SpecificationsUseable Sensitivity14dBF which is 1.4uV across 75 ohms50dB Quieting SensitivityMono: 19dBF which is 2.4uV across 75 ohmsStere
67Packing InstructionsQuantity Part Number Description1 034158 Shipping carton only2 034250 Foam end cap1 034198 Inner carton top1 034199 Inner carton
McIntosh Laboratory, Inc.2 Chambers StreetBinghamton, NY 13903The continuous improvement of its products isthe policy of McIntosh Laboratory Incorpora
7Performance FeaturesIntroduction••••• On Screen and Multifunction Fluorescent DisplaysA comprehensive On-Screen Display capability makes iteasy to pe
8DimensionsThe following dimensions can assist in determining thebest location for your MHT200. There is additional infor-mation on the next page pert
9InstallationThe MHT200 can be placed upright on a table or shelf,standing on its four feet. It also can be custom installed in apiece of furniture or
Commentaires sur ces manuels