McIntosh MCD 7007 Instructions d'exploitation télécharger pdf (Page 16)

The greatest care has been taken in the

manufacture of your Mclntosh Compact Disc player.

In case of operational difficulties and to save you

unnecessary service calls, here is a list of their

possible causes and suggested solutions. Should you

need further guidance, contact your dealer. He will

be able to advise you. Under no circumstances

should you open up the player. To do so can void

the service contract.

1. After touching POWER, the track indicator does not

light.

• Touch the POWER button again. POWER was not

pressed in far enough. They require only .007"

movement to engage.

• The player is not properly plugged into the 120V

AC supply.

• There is no 120V AC supply. Plug in another

electrical appliance and see if it functions in the

same outlet.

2. After touching LOAD, the disc drawer does not slide

out.

• The player is not switched on and the message

center data will not light.

• The microprocessor has not received the

command correctly. Touch STOP and then touch

LOAD again to see if the drawer opens.

• The drawer drive is not functioning. You cannot

correct this yourself. If a disc is in position,

remove it by pulling the drawer open carefully,

then push the drawer in to close it again.

3. After touching LOAD, PLAY or SCAN, the disc

drawer does not slide in.

• The 120 VAC supply has been disconnected and

the track indicator will not light.

• The microprocessor has not received the correct

command. Touch STOP and then touch LOAD,

PLAY or SCAN again to see if the drawer closes.

• The drawer drive is not functioning. You cannot

correct this yourself. If a disc is in position,

remove it, than push the drawer in carefully to

close it.

4. After closing the drawer the Message Center Data

shows the 'OoOoo' and the DISC and ERROR light

and nothing further happens.

• The transport screws have not been removed.

• The disc is not inserted label up or there isn't a

disc in the drawer and you have missed the

ERROR DISC sign.

• The disc is dirty. Clean the disc, or use another,

clean disc.

• The disc is defective. See if another disc clears the

problem.

• There is an unwanted object in the disc drawer,

such as a piece of paper or a remnant of the

packaging.

• The player is not horizontal.

5. The disc is being played as shown by the time elaps-

ed indicator, but there isn't any sound.

• The microprocessor has not received the correct

command. Check if touching STOP and then re-

starting clears the problem.

• The preamplifier is not switched on.

• The preamplifier source selector is not turned to

the input to which the player is connected.

• The preamplifier, amplifier or the loudspeakers

connected to it are not working. Check with

another sound source.

• The connection between the player and the

preamplifier is broken.

• The input to which the player is connected is

defective. Check by connecting the player to

another input.

• Volume control is turned down.

• Player in PAUSE mode

6. The sound is poor or distorted or you can hear only

one channel.

• The transport screws have not been removed.

• The disc is dirty or badly scratched. Clean the disc

or use another clean, scratch-free disc.

• There is an unwanted object in the disc drawer,

such as a piece of paper or a remnant of

packaging.

• The preamplifier or the loudspeakers connected to

it are not working properly. Check with another

sound source.

• The player is connected to the PHONO input not

the CD, AUX, or other high level input of the

preamplifier.

• One of the plugs of the connecting cable is either

not connected or not properly connected.

• The player is not horizontal.

14 HELPFUL HINTS

1 2 ... 11 12 13 14 15 16 17 18 19 20

Commentaires sur ces manuels

Pas de commentaire

McIntosh MCD 7007 Instructions d'exploitation Page 16

Commentaires sur ces manuels

Produits connexes et manuels pour Lecteurs de CD McIntosh MCD 7007