Mcintosh C2300 Manuel d'utilisateur télécharger pdf (Page 18)

METER ILLUMINATION

The C2300 Front Panel Meter Illumination may be

switched On or Off by performing the following:

1. Rotate the TRIM SELECT Control or press the TRIM

Push-button on the Remote Control until “METER

ON” appears on the Front Panel Alphanumeric Display.

2. Rotate the TRIM ADJUST Control or press the LEV-

EL + / - Push-buttons to switch On or Off the Meter

Illumination.

After approximately 3 seconds the Alphanumeric Display

returns to the indicate the Source Selection and Volume

Level.

Note: When the Main Power Control of the C2300 is connect-

ed to a McIntosh Power Amplifier with Remote Meter

Illumination Control the C2300 Meter Illumination

Setting of On or Off will also affect the Power Amplifer

Meter Illumination.

PHONO ADJUSTMENTS

When the Phono MC or Phono MM Input is selected an

additional TRIM SELECT FUNCTION becomes available

for adjustment. Perform the following steps to make the

Phono Trim Adjustments:

1. Select either the Phono MM or Phono MC Input using

the INPUT Control.

2. Rotate the TRIM SELECT Control or press the TRIM

Push-button on the Remote Control until “PHMM _ _

_ PF” or “PHMC _ _ _ OHM” appears on the Front

Panel Alphanumeric Display. Refer to figures 22 and

23.

3. Rotate the TRIM ADJUST Control or press the

LEVEL + / - Push-buttons to select from the avail

able values of cartridge loading (Ohms for a Moving

Coil Cartridge or Capacitance for a Moving Magnet

Cartridge) that comes closest to the Cartridge Makers

recommend value.

After approximately 3 seconds the Alphanumeric Display

returns to the indicate the Source Selection and Volume

Level.

Tone Bypass

Press the TONE BYPASS Push-button to Bypass the Tone

Control Circuitry, providing a flat frequency response. If

How to Operate the C2300, con’t

the AUTOTONE circuit is set to the On position in Setup

Mode, the C2300 will remember for each input whether the

Tone Bypass is active. The Front Panel LED will illumi-

nate indicating the BYPASS Mode is active.

Mono

Press the Front Panel MONO Push-button or the MODE

Push-button on the Remote Control to combine left and

right stereo signals to a Monophonic Signal. The Front

Panel LED will illuminate indicating the MONO Mode is

active. The C2300 automatically stores into memory for

each Input, the Selection of the Stereo or Mono Mode.

Note: The signals at the SRVR OUT (REC) Jacks are not

affected.

Record Monitor

Press the REC MONITOR Push-button to hear the SERV-

ER Playback Signal during the recording process.

Setup

Pressing the SETUP Push-button activates the Setup Mode

of the C2300 and allows customizing various operating

functions. Refer to page 11 for additional information.

Mute

Press the MUTE Push-button, on the C2300 Front Panel

or on the Remote Control, to Mute the Audio at the OUT

PUTS Connectors and HEADPHONES Output Jack. The

Front Panel Alphanumeric Display will indicate the Input

Source Name followed by the word MUTE in place of the

actual volume setting. Refer to figure 24.

Pressing the Mute Push-button a second time or adjust-

ing the volume control (either the Front Panel or Remote

Control) will un-mute the C2300.

If the Front Panel MUTE Push-button is pressed for at

least 3 seconds, the C2300 will mute the OUTPUTS con-

nectors, yet listening with headphones will continue until

the Mute Push-button is pressed again for 3 seconds. The

Front Panel Alphanumeric Display will indicate the Input

Source Name, Volume Setting and a Dot. Refer to figures

25 and 26.

Figure 22

Figure 23

Figure 24

Figure 25

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 24

Commentaires sur ces manuels

Pas de commentaire

Mcintosh C2300 Manuel d'utilisateur Page 18

Commentaires sur ces manuels

Produits connexes et manuels pour Récepteurs et amplificateurs Mcintosh C2300